1 Laser engraving machine should be used in strict accordance with the correct start-up sequence of power on or off. Note: the laser power supply must be preheated for 5 minutes!
2 in the laser engraving machine work development process, must be carried out at any time you can detect the system water temperature (the best management work environment water temperature of 25 ~ 30 ℃, the highest water temperature can not have no more than 35 ℃, the lowest water temperature can not be significantly lower than 5 ℃), once the water has a warm feeling, should immediately change the water. Does not affect the work of the enterprise water change method is: discharge a part of the use of hot water, and then flushed into the cold water.
3. Every month, must clean the laser machine water tank, water pump (especially the water pump filter sponge) and laserpecker pro 2in and out of the water hose. Engraving machine of other peripheral equipment (such as: fan, air pump, etc.) also need to clean.
4 Regularly check and measure the grounding to determine if it is working properly.
Periodically (once every half month or so) test the water protection switch to determine if it is working properly.
Before turning on the machine every day, observe whether the focusing lens of the laser machine is contaminated, and clean it promptly if it is. When cleaning the reflector, please be careful not to use too much force, or it will cause the light path to be shifted! Maintenance of reflectors and focusing lenses at all levels should follow the principle of "timely cleaning of contamination". Cleaning must use special lens cleaner.
7 every day before the start of work analysis, please test the system whether the limit switches can staff normal, to ensure that the enterprise equipment in the process of work development we will not change the collision affecting the accuracy of the teaching equipment; each time the equipment before the safe work, please pay attention to adjust the focal length and lock to ensure that not because of the decline in the focal length of the country's processing effect, or even the occurrence of a mechanical collision.
8. Every day after the end of the equipment work, laserpecker laser engraver should do a good job of cleaning. In the case of power outage, you can slowly push the focusing lens set and X-axis guide seat, no violent push and pull. The bed should be kept clean, especially the two linear guide rails, guide rails ,laserpecker 1 pro and guide seats should be cleaned at the end of each day's work;.
9 Screw and coupling tightening motion system after working for a period of time, the screw and coupling at the movable joints will become loose, affecting the stability of mechanical movement. Therefore, it is necessary to observe the machine operation process of the transmission components whether there is a strange sound or anomaly, found that the problem in a timely manner to strengthen the maintenance. At the same time the machine after a period of time to use tools to strengthen the screws one by one. The first hardening should be about one month after the equipment is used.
10 laser engraving machine optical system is completed by the reflection of the mirror and focusing mirror focusing. The focusing mirror has no deviation problem in the optical system, but the triple reflector is fixed by the mechanical part, and the possibility of deviation is high, although it usually does not happen, but it is recommended that the user check every work before the optical path is normal.
11 equipment in the operation and management process, due to the processed parts in the processing process will produce the need for a large number of corrosive dust and smoke, based on these smoke and dust for a long time there is a large number of deposits in the guide rail, linear axis surface, the processing accuracy of the equipment has a great impact on the development of the equipment, and we will be in the guide rail linear axis surface can be formed etching, shorten the service life of the production equipment through the service life. In order to make the machine normal social stability enterprise work, to ensure that the company's products processing service quality, to seriously learn to do a good job of the guide rail, linear axis of the daily maintenance.
Linear guide cleaning: first of all, move the laser head to the far right (or left), find the linear guide as shown in the figure above, wipe with a dry cotton cloth to bright and dust-free, add a little lubricant (you can use sewing machine oil, but do not use machine oil), slowly push the laser head left and right a few times, so that the lubricant is evenly distributed.